Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Everybody may have their own individual opinions with regards to How to Install a Bathtub Yourself.
Setting up a bathtub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old tub is conveniently accessible, the project can move quickly; if you need to open a wall surface to remove the old tub as well as position the brand-new tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and fit attempting it. Instead of employing a professional to take over a halfway-completed job, it is far better to consider utilizing one before you start. Opportunities are you may need a professional plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your bathroom if you have already purchased a brand-new tub and also don't require to change the plan of your previous water pipelines.
Your devices as well as material list need to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be rather bothersome due to the limited accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. When the supply pipes have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in place in between the faucet and also the sink. Secure the tap in position with the manufacturer provided backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former type should be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of both wood boards under its feet, put the bathtub in the required position. The wood boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level as well as adjusting the feet on the bath tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water supply and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it right into its final setting.
Getting ready for the Installation
First of all, the sustaining frame supplied with the bath must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, creating the water to pass through the wall in between the bath and also the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can fracture fairly very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that write-up about Installing A Bathtub through an acquaintance on a different web property. In case you enjoyed reading our page kindly don't forget to share it. I thank you for reading our article about Installing A Bathtub.
Free Estimates Report this page